[ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 2.6.26-2-amd64 (Debian 2.6.26-17) (dannf@debian.org) (gcc version 4.1.3 20080704 (prerelease) (Debian 4.1.2-25)) #1 SMP Sun Jun 21 04:47:08 UTC 2009 [ 0.000000] Command line: root=/dev/mapper/lvm-dom0--root ro console=tty0 console=ttyS0,115200 [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f000 (usable) [ 0.000000] BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved) [ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) [ 0.000000] BIOS-e820: 0000000000100000 - 00000000dfee0000 (usable) [ 0.000000] BIOS-e820: 00000000dfee0000 - 00000000dfee3000 (ACPI NVS) [ 0.000000] BIOS-e820: 00000000dfee3000 - 00000000dfef0000 (ACPI data) [ 0.000000] BIOS-e820: 00000000dfef0000 - 00000000dff00000 (reserved) [ 0.000000] BIOS-e820: 00000000f0000000 - 00000000f4000000 (reserved) [ 0.000000] BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved) [ 0.000000] BIOS-e820: 0000000100000000 - 0000000120000000 (usable) [ 0.000000] Entering add_active_range(0, 0, 159) 0 entries of 3200 used [ 0.000000] Entering add_active_range(0, 256, 917216) 1 entries of 3200 used [ 0.000000] Entering add_active_range(0, 1048576, 1179648) 2 entries of 3200 used [ 0.000000] max_pfn_mapped = 1179648 [ 0.000000] init_memory_mapping [ 0.000000] DMI 2.4 present. [ 0.000000] ACPI: RSDP 000F7620, 0024 (r2 Nvidia) [ 0.000000] ACPI: XSDT DFEE30C0, 0044 (r1 Nvidia ASUSACPI 42302E31 AWRD 0) [ 0.000000] ACPI: FACP DFEEC480, 00F4 (r3 Nvidia ASUSACPI 42302E31 AWRD 0) [ 0.000000] ACPI: DSDT DFEE3240, 91E0 (r1 NVIDIA AWRDACPI 1000 MSFT 3000000) [ 0.000000] ACPI: FACS DFEE0000, 0040 [ 0.000000] ACPI: HPET DFEEC680, 0038 (r1 Nvidia ASUSACPI 42302E31 AWRD 98) [ 0.000000] ACPI: MCFG DFEEC700, 003C (r1 Nvidia ASUSACPI 42302E31 AWRD 0) [ 0.000000] ACPI: APIC DFEEC5C0, 007C (r1 Nvidia ASUSACPI 42302E31 AWRD 0) [ 0.000000] Scanning NUMA topology in Northbridge 24 [ 0.000000] No NUMA configuration found [ 0.000000] Faking a node at 0000000000000000-0000000120000000 [ 0.000000] Entering add_active_range(0, 0, 159) 0 entries of 3200 used [ 0.000000] Entering add_active_range(0, 256, 917216) 1 entries of 3200 used [ 0.000000] Entering add_active_range(0, 1048576, 1179648) 2 entries of 3200 used [ 0.000000] Bootmem setup node 0 0000000000000000-0000000120000000 [ 0.000000] NODE_DATA [000000000000e000 - 0000000000012fff] [ 0.000000] bootmap [0000000000013000 - 0000000000036fff] pages 24 [ 0.000000] early res: 0 [0-fff] BIOS data page [ 0.000000] early res: 1 [6000-7fff] TRAMPOLINE [ 0.000000] early res: 2 [200000-673397] TEXT DATA BSS [ 0.000000] early res: 3 [37885000-37fef464] RAMDISK [ 0.000000] early res: 4 [9f000-fffff] BIOS reserved [ 0.000000] early res: 5 [8000-dfff] PGTABLE [ 0.000000] [ffffe20000000000-ffffe20002dfffff] PMD -> [ffff810001200000-ffff810003ffffff] on node 0 [ 0.000000] [ffffe20002e00000-ffffe20003ffffff] PMD -> [ffff81000c000000-ffff81000cbfffff] on node 0 [ 0.000000] Zone PFN ranges: [ 0.000000] DMA 0 -> 4096 [ 0.000000] DMA32 4096 -> 1048576 [ 0.000000] Normal 1048576 -> 1179648 [ 0.000000] Movable zone start PFN for each node [ 0.000000] early_node_map[3] active PFN ranges [ 0.000000] 0: 0 -> 159 [ 0.000000] 0: 256 -> 917216 [ 0.000000] 0: 1048576 -> 1179648 [ 0.000000] On node 0 totalpages: 1048191 [ 0.000000] DMA zone: 56 pages used for memmap [ 0.000000] DMA zone: 1247 pages reserved [ 0.000000] DMA zone: 2696 pages, LIFO batch:0 [ 0.000000] DMA32 zone: 14280 pages used for memmap [ 0.000000] DMA32 zone: 898840 pages, LIFO batch:31 [ 0.000000] Normal zone: 1792 pages used for memmap [ 0.000000] Normal zone: 129280 pages, LIFO batch:31 [ 0.000000] Movable zone: 0 pages used for memmap [ 0.000000] ACPI: PM-Timer IO Port: 0x1008 [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) [ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) [ 0.000000] IOAPIC[0]: apic_id 2, version 0, address 0xfec00000, GSI 0-23 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge) [ 0.000000] ACPI: IRQ0 used by override. [ 0.000000] ACPI: IRQ2 used by override. [ 0.000000] ACPI: IRQ9 used by override. [ 0.000000] ACPI: IRQ14 used by override. [ 0.000000] ACPI: IRQ15 used by override. [ 0.000000] Setting APIC routing to flat [ 0.000000] ACPI: HPET id: 0x10de8201 base: 0xfefff000 [ 0.000000] Using ACPI (MADT) for SMP configuration information [ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000 [ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000f0000 [ 0.000000] PM: Registered nosave memory: 00000000000f0000 - 0000000000100000 [ 0.000000] PM: Registered nosave memory: 00000000dfee0000 - 00000000dfee3000 [ 0.000000] PM: Registered nosave memory: 00000000dfee3000 - 00000000dfef0000 [ 0.000000] PM: Registered nosave memory: 00000000dfef0000 - 00000000dff00000 [ 0.000000] PM: Registered nosave memory: 00000000dff00000 - 00000000f0000000 [ 0.000000] PM: Registered nosave memory: 00000000f0000000 - 00000000f4000000 [ 0.000000] PM: Registered nosave memory: 00000000f4000000 - 00000000fec00000 [ 0.000000] PM: Registered nosave memory: 00000000fec00000 - 0000000100000000 [ 0.000000] Allocating PCI resources starting at e0000000 (gap: dff00000:10100000) [ 0.000000] SMP: Allowing 2 CPUs, 0 hotplug CPUs [ 0.000000] PERCPU: Allocating 37168 bytes of per cpu data [ 0.000000] NR_CPUS: 32, nr_cpu_ids: 2 [ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 1030816 [ 0.000000] Policy zone: Normal [ 0.000000] Kernel command line: root=/dev/mapper/lvm-dom0--root ro console=tty0 console=ttyS0,115200 [ 0.000000] Initializing CPU#0 [ 0.000000] PID hash table entries: 4096 (order: 12, 32768 bytes) [ 0.000000] Extended CMOS year: 2000 [ 0.000000] TSC calibrated against PM_TIMER [ 0.000000] Marking TSC unstable due to TSCs unsynchronized [ 0.000000] time.c: Detected 2210.179 MHz processor. [ 0.004000] spurious 8259A interrupt: IRQ7. [ 0.004000] Console: colour VGA+ 80x25 [ 0.004000] console [tty0] enabled [ 0.004000] console [ttyS0] enabled [ 0.004000] Checking aperture... [ 0.004000] Node 0: aperture @ 4000000 size 32 MB [ 0.004000] Aperture pointing to e820 RAM. Ignoring. [ 0.004000] No AGP bridge found [ 0.004000] Your BIOS doesn't leave a aperture memory hole [ 0.004000] Please enable the IOMMU option in the BIOS setup [ 0.004000] This costs you 64 MB of RAM [ 0.004000] Mapping aperture over 65536 KB of RAM @ 4000000 [ 0.004000] PM: Registered nosave memory: 0000000004000000 - 0000000008000000 [ 0.004000] Memory: 4055332k/4718592k available (2225k kernel code, 137432k reserved, 1080k data, 392k init) [ 0.004000] CPA: page pool initialized 1 of 1 pages preallocated [ 0.004000] hpet clockevent registered [ 0.083942] Calibrating delay using timer specific routine.. 4423.87 BogoMIPS (lpj=8847758) [ 0.090869] Security Framework initialized [ 0.094992] SELinux: Disabled at boot. [ 0.098853] Capability LSM initialized [ 0.102996] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes) [ 0.109894] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes) [ 0.116007] Mount-cache hash table entries: 256 [ 0.120007] Initializing cgroup subsys ns [ 0.124007] Initializing cgroup subsys cpuacct [ 0.128008] Initializing cgroup subsys devices [ 0.132008] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) [ 0.136008] CPU: L2 Cache: 512K (64 bytes/line) [ 0.140008] CPU 0/0 -> Node 0 [ 0.143005] CPU: Physical Processor ID: 0 [ 0.147032] CPU: Processor Core ID: 0 [ 0.151379] ACPI: Core revision 20080321 [ 0.209478] CPU0: AMD Athlon(tm) 64 X2 Dual Core Processor 4200+ stepping 02 [ 0.216013] Using local APIC timer interrupts. [ 0.224014] APIC timer calibration result 12557853 [ 0.224014] Detected 12.557 MHz APIC timer. [ 0.228014] Booting processor 1/1 ip 6000 [ 0.240015] Initializing CPU#1 [ 0.240015] Calibrating delay using timer specific routine.. 4420.45 BogoMIPS (lpj=8840906) [ 0.240015] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) [ 0.240015] CPU: L2 Cache: 512K (64 bytes/line) [ 0.240015] CPU 1/1 -> Node 0 [ 0.240015] CPU: Physical Processor ID: 0 [ 0.240015] CPU: Processor Core ID: 1 [ 0.319904] CPU1: AMD Athlon(tm) 64 X2 Dual Core Processor 4200+ stepping 02 [ 0.329286] Brought up 2 CPUs [ 0.332275] Total of 2 processors activated (8844.33 BogoMIPS). [ 0.338352] CPU0 attaching sched-domain: [ 0.338355] domain 0: span 0-1 [ 0.338357] groups: 0 1 [ 0.338360] domain 1: span 0-1 [ 0.338361] groups: 0-1 [ 0.338365] CPU1 attaching sched-domain: [ 0.338366] domain 0: span 0-1 [ 0.338368] groups: 1 0 [ 0.338371] domain 1: span 0-1 [ 0.338372] groups: 0-1 [ 0.340021] net_namespace: 1224 bytes [ 0.343705] Booting paravirtualized kernel on bare hardware [ 0.348021] NET: Registered protocol family 16 [ 0.352022] node 0 link 0: io port [9000, ffff] [ 0.352022] TOM: 00000000e0000000 aka 3584M [ 0.356022] node 0 link 0: mmio [a0000, bffff] [ 0.356022] node 0 link 0: mmio [e0000000, efffffff] [ 0.356022] node 0 link 0: mmio [f4000000, fe02ffff] [ 0.356022] node 0 link 0: mmio [f0000000, f07fffff] [ 0.356022] TOM2: 0000000120000000 aka 4608M [ 0.360022] bus: [00,07] on node 0 link 0 [ 0.360022] bus: 00 index 0 io port: [0, ffff] [ 0.360022] bus: 00 index 1 mmio: [a0000, bffff] [ 0.360022] bus: 00 index 2 mmio: [e0000000, f3ffffff] [ 0.360022] bus: 00 index 3 mmio: [f4000000, ffffffff] [ 0.360022] bus: 00 index 4 mmio: [120000000, fcffffffff] [ 0.360022] ACPI: bus type pci registered [ 0.364022] PCI: MCFG configuration 0: base f0000000 segment 0 buses 0 - 63 [ 0.368023] PCI: MCFG area at f0000000 reserved in E820 [ 0.376023] PCI: Using MMCONFIG at f0000000 - f3ffffff [ 0.380060] PCI: Using configuration type 1 for base access [ 0.384060] ACPI: EC: Look up EC in DSDT [ 0.396024] ACPI: Interpreter enabled [ 0.400023] ACPI: (supports S0 S1 S3 S4 S5) [ 0.404443] ACPI: Using IOAPIC for interrupt routing [ 0.420920] ACPI: PCI Root Bridge [PCI0] (0000:00) [ 0.425538] PCI: Transparent bridge - 0000:00:06.0 [ 0.433044] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] [ 0.433564] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT] [ 0.540145] ACPI: PCI Interrupt Link [LNK1] (IRQs 5 7 9 10 *11 14 15) [ 0.544146] ACPI: PCI Interrupt Link [LNK2] (IRQs 5 7 9 10 11 14 15) *0, disabled. [ 0.554048] ACPI: PCI Interrupt Link [LNK3] (IRQs 5 7 9 10 11 14 15) *0, disabled. [ 0.562023] ACPI: PCI Interrupt Link [LNK4] (IRQs 5 7 9 10 11 14 15) *0, disabled. [ 0.570048] ACPI: PCI Interrupt Link [LNK5] (IRQs 5 7 9 10 11 14 15) *0, disabled. [ 0.574348] ACPI: PCI Interrupt Link [LNK6] (IRQs 5 7 9 *10 11 14 15) [ 0.578348] ACPI: PCI Interrupt Link [LNK7] (IRQs *5 7 9 10 11 14 15) [ 0.584848] ACPI: PCI Interrupt Link [LNK8] (IRQs 5 7 9 10 11 14 15) *0, disabled. [ 0.593150] ACPI: PCI Interrupt Link [LP2P] (IRQs 5 7 9 10 11 14 15) *0, disabled. [ 0.601447] ACPI: PCI Interrupt Link [LUBA] (IRQs 5 7 9 10 *11 14 15) [ 0.608489] ACPI: PCI Interrupt Link [LMAC] (IRQs 5 7 9 *10 11 14 15) [ 0.615528] ACPI: PCI Interrupt Link [LAZA] (IRQs 5 7 9 10 *11 14 15) [ 0.622434] ACPI: PCI Interrupt Link [LPMU] (IRQs 5 7 9 10 11 14 15) *0, disabled. [ 0.626434] ACPI: PCI Interrupt Link [LSMB] (IRQs 5 7 9 *10 11 14 15) [ 0.630434] ACPI: PCI Interrupt Link [LUB2] (IRQs *5 7 9 10 11 14 15) [ 0.636923] ACPI: PCI Interrupt Link [LIDE] (IRQs 5 7 9 10 11 14 15) *0, disabled. [ 0.645160] ACPI: PCI Interrupt Link [LSID] (IRQs 5 7 9 *10 11 14 15) [ 0.652209] ACPI: PCI Interrupt Link [LFID] (IRQs 5 7 9 10 *11 14 15) [ 0.659297] ACPI: PCI Interrupt Link [LSA2] (IRQs *5 7 9 10 11 14 15) [ 0.666383] ACPI: PCI Interrupt Link [APC1] (IRQs 16) *0 [ 0.671696] ACPI: PCI Interrupt Link [APC2] (IRQs 17) *0, disabled. [ 0.678441] ACPI: PCI Interrupt Link [APC3] (IRQs 18) *0, disabled. [ 0.682496] ACPI: PCI Interrupt Link [APC4] (IRQs 19) *0, disabled. [ 0.688682] ACPI: PCI Interrupt Link [APC5] (IRQs 16) *0, disabled. [ 0.694496] ACPI: PCI Interrupt Link [APC6] (IRQs 16) *0 [ 0.698496] ACPI: PCI Interrupt Link [APC7] (IRQs 16) *0 [ 0.702496] ACPI: PCI Interrupt Link [APC8] (IRQs 16) *0, disabled. [ 0.709191] ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22 23) *0 [ 0.715832] ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22 23) *0 [ 0.722458] ACPI: PCI Interrupt Link [APMU] (IRQs 20 21 22 23) *0, disabled. [ 0.726987] ACPI: PCI Interrupt Link [AAZA] (IRQs 20 21 22 23) *0 [ 0.733077] ACPI: PCI Interrupt Link [APCS] (IRQs 20 21 22 23) *0 [ 0.739724] ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22 23) *0 [ 0.746389] ACPI: PCI Interrupt Link [APCM] (IRQs 20 21 22 23) *0, disabled. [ 0.754028] ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22 23) *0, disabled. [ 0.761692] ACPI: PCI Interrupt Link [APSI] (IRQs 20 21 22 23) *0 [ 0.768364] ACPI: PCI Interrupt Link [APSJ] (IRQs 20 21 22 23) *0 [ 0.775000] ACPI: PCI Interrupt Link [ASA2] (IRQs 20 21 22 23) *0 [ 0.779000] Linux Plug and Play Support v0.97 (c) Adam Belay [ 0.783000] pnp: PnP ACPI init [ 0.786083] ACPI: bus type pnp registered [ 0.790224] pnp 00:00: parse allocated resources [ 0.795000] pnp 00:00: add io 0xcf8-0xcff flags 0x1 [ 0.795167] pnp 00:00: Plug and Play ACPI device, IDs PNP0a08 PNP0a03 (active) [ 0.795180] pnp 00:01: parse allocated resources [ 0.795244] pnp 00:01: add io 0x1000-0x107f flags 0x1 [ 0.795246] pnp 00:01: add io 0x1080-0x10ff flags 0x1 [ 0.795249] pnp 00:01: add io 0x1400-0x147f flags 0x1 [ 0.795251] pnp 00:01: add io 0x1480-0x14ff flags 0x1 [ 0.795253] pnp 00:01: add io 0x1800-0x187f flags 0x1 [ 0.795255] pnp 00:01: add io 0x1880-0x18ff flags 0x1 [ 0.795259] pnp 00:01: PNP0c02: calling quirk_system_pci_resources+0x0/0x15c [ 0.795433] pnp 00:01: Plug and Play ACPI device, IDs PNP0c02 (active) [ 0.797896] pnp 00:02: parse allocated resources [ 0.797902] pnp 00:02: add io 0x10-0x1f flags 0x1 [ 0.797905] pnp 00:02: add io 0x22-0x3f flags 0x1 [ 0.797907] pnp 00:02: add io 0x44-0x5f flags 0x1 [ 0.797909] pnp 00:02: add io 0x62-0x63 flags 0x1 [ 0.797911] pnp 00:02: add io 0x65-0x6f flags 0x1 [ 0.797914] pnp 00:02: add io 0x74-0x7f flags 0x1 [ 0.797916] pnp 00:02: add io 0x91-0x93 flags 0x1 [ 0.797919] pnp 00:02: add io 0xa2-0xbf flags 0x1 [ 0.797921] pnp 00:02: add io 0xe0-0xef flags 0x1 [ 0.797923] pnp 00:02: add io 0x4d0-0x4d1 flags 0x1 [ 0.797925] pnp 00:02: add io 0x800-0x87f flags 0x1 [ 0.797927] pnp 00:02: add io 0x290-0x297 flags 0x1 [ 0.797930] pnp 00:02: PNP0c02: calling quirk_system_pci_resources+0x0/0x15c [ 0.798109] pnp 00:02: Plug and Play ACPI device, IDs PNP0c02 (active) [ 0.798124] pnp 00:03: parse allocated resources [ 0.798130] pnp 00:03: add dma 4 flags 0x4 [ 0.798132] pnp 00:03: add io 0x0-0xf flags 0x1 [ 0.798134] pnp 00:03: add io 0x80-0x90 flags 0x1 [ 0.798136] pnp 00:03: add io 0x94-0x9f flags 0x1 [ 0.798138] pnp 00:03: add io 0xc0-0xdf flags 0x1 [ 0.798294] pnp 00:03: Plug and Play ACPI device, IDs PNP0200 (active) [ 0.798374] pnp 00:04: parse allocated resources [ 0.798453] pnp 00:04: add irq 8 flags 0x1 [ 0.798455] pnp 00:04: add mem 0xfefff000-0xfefff3ff flags 0x1 [ 0.798614] pnp 00:04: Plug and Play ACPI device, IDs PNP0103 (active) [ 0.798628] pnp 00:05: parse allocated resources [ 0.798700] pnp 00:05: add io 0x70-0x73 flags 0x1 [ 0.798833] pnp 00:05: Plug and Play ACPI device, IDs PNP0b00 (active) [ 0.798833] pnp 00:06: parse allocated resources [ 0.798833] pnp 00:06: add io 0x61-0x61 flags 0x1 [ 0.798833] pnp 00:06: Plug and Play ACPI device, IDs PNP0800 (active) [ 0.798833] pnp 00:07: parse allocated resources [ 0.798833] pnp 00:07: add io 0xf0-0xff flags 0x1 [ 0.798833] pnp 00:07: add irq 13 flags 0x1 [ 0.798833] pnp 00:07: Plug and Play ACPI device, IDs PNP0c04 (active) [ 0.798833] pnp 00:08: parse allocated resources [ 0.798833] pnp 00:08: add io 0x3f0-0x3f5 flags 0x1 [ 0.798833] pnp 00:08: add io 0x3f7-0x3f7 flags 0x1 [ 0.798843] pnp 00:08: add irq 6 flags 0x1 [ 0.798845] pnp 00:08: add dma 2 flags 0x0 [ 0.798847] pnp 00:08: parse resource options [ 0.798849] pnp 00:08: new independent option [ 0.798854] pnp 00:08: new dependent option (priority 0x1) [ 0.798857] pnp 00:08: io min 0x3f0 max 0x3f0 align 1 size 6 flags 0x1 [ 0.798860] pnp 00:08: io min 0x3f7 max 0x3f7 align 1 size 1 flags 0x1 [ 0.798865] pnp 00:08: irq bitmask 00000000,00000000,00000000,00000000,00000000,00000000,00000000,00000040 flags 0x1 [ 0.798868] pnp 00:08: dma bitmask 0x4 flags 0x0 [ 0.798870] pnp 00:08: end dependent options [ 0.802833] pnp 00:08: Plug and Play ACPI device, IDs PNP0700 (active) [ 0.802833] pnp 00:09: parse allocated resources [ 0.802833] pnp 00:09: add io 0x3f8-0x3ff flags 0x1 [ 0.802833] pnp 00:09: add irq 4 flags 0x1 [ 0.802833] pnp 00:09: parse resource options [ 0.802833] pnp 00:09: new independent option [ 0.802833] pnp 00:09: new dependent option (priority 0x1) [ 0.802833] pnp 00:09: io min 0x3f8 max 0x3f8 align 1 size 8 flags 0x1 [ 0.802833] pnp 00:09: irq bitmask 00000000,00000000,00000000,00000000,00000000,00000000,00000000,00001eb8 flags 0x1 [ 0.802833] pnp 00:09: new dependent option (priority 0x1) [ 0.802833] pnp 00:09: io min 0x2f8 max 0x2f8 align 1 size 8 flags 0x1 [ 0.802833] pnp 00:09: irq bitmask 00000000,00000000,00000000,00000000,00000000,00000000,00000000,00001eb8 flags 0x1 [ 0.802833] pnp 00:09: new dependent option (priority 0x1) [ 0.802833] pnp 00:09: io min 0x3e8 max 0x3e8 align 1 size 8 flags 0x1 [ 0.802833] pnp 00:09: irq bitmask 00000000,00000000,00000000,00000000,00000000,00000000,00000000,00001eb8 flags 0x1 [ 0.802833] pnp 00:09: new dependent option (priority 0x1) [ 0.802833] pnp 00:09: io min 0x2e8 max 0x2e8 align 1 size 8 flags 0x1 [ 0.802833] pnp 00:09: irq bitmask 00000000,00000000,00000000,00000000,00000000,00000000,00000000,00001eb8 flags 0x1 [ 0.802833] pnp 00:09: end dependent options [ 0.802833] pnp 00:09: Plug and Play ACPI device, IDs PNP0501 (active) [ 0.802833] pnp 00:0a: parse allocated resources [ 0.802833] pnp 00:0a: add io 0x378-0x37f flags 0x1 [ 0.802833] pnp 00:0a: add irq 7 flags 0x1 [ 0.802833] pnp 00:0a: parse resource options [ 0.802833] pnp 00:0a: new independent option [ 0.802833] pnp 00:0a: new dependent option (priority 0x1) [ 0.802833] pnp 00:0a: io min 0x378 max 0x378 align 1 size 8 flags 0x1 [ 0.802833] pnp 00:0a: irq bitmask 00000000,00000000,00000000,00000000,00000000,00000000,00000000,00001eb8 flags 0x1 [ 0.802833] pnp 00:0a: new dependent option (priority 0x1) [ 0.802833] pnp 00:0a: io min 0x278 max 0x278 align 1 size 8 flags 0x1 [ 0.802833] pnp 00:0a: irq bitmask 00000000,00000000,00000000,00000000,00000000,00000000,00000000,00001eb8 flags 0x1 [ 0.802833] pnp 00:0a: new dependent option (priority 0x1) [ 0.802833] pnp 00:0a: io min 0x3bc max 0x3bc align 1 size 4 flags 0x1 [ 0.802833] pnp 00:0a: irq bitmask 00000000,00000000,00000000,00000000,00000000,00000000,00000000,00001eb8 flags 0x1 [ 0.802833] pnp 00:0a: end dependent options [ 0.802833] pnp 00:0a: Plug and Play ACPI device, IDs PNP0400 (active) [ 0.802833] pnp 00:0b: parse allocated resources [ 0.802833] pnp 00:0b: add mem 0xf0000000-0xf3ffffff flags 0x1 [ 0.802833] pnp 00:0b: PNP0c02: calling quirk_system_pci_resources+0x0/0x15c [ 0.802833] pnp 00:0b: Plug and Play ACPI device, IDs PNP0c02 (active) [ 0.802833] pnp 00:0c: parse allocated resources [ 0.802833] pnp 00:0c: add mem 0xcf400-0xcffff flags 0x1 [ 0.802833] pnp 00:0c: add mem 0xf0000-0xf7fff flags 0x1 [ 0.802833] pnp 00:0c: add mem 0xf8000-0xfbfff flags 0x1 [ 0.802833] pnp 00:0c: add mem 0xfc000-0xfffff flags 0x1 [ 0.802833] pnp 00:0c: add mem 0xfefff000-0xfefff0ff flags 0x1 [ 0.802833] pnp 00:0c: add mem 0xdfee0000-0xdfefffff flags 0x1 [ 0.802833] pnp 00:0c: add mem 0xffff0000-0xffffffff flags 0x1 [ 0.802833] pnp 00:0c: add mem 0x0-0x9ffff flags 0x1 [ 0.802833] pnp 00:0c: add mem 0x100000-0xdfedffff flags 0x1 [ 0.802833] pnp 00:0c: add mem 0xfec00000-0xfec00fff flags 0x1 [ 0.802833] pnp 00:0c: add mem 0xfee00000-0xfeefffff flags 0x1 [ 0.802833] pnp 00:0c: add mem 0xfefff000-0xfeffffff flags 0x1 [ 0.802833] pnp 00:0c: add mem 0xfff80000-0xfff80fff flags 0x1 [ 0.802833] pnp 00:0c: add mem 0xfff90000-0xfffbffff flags 0x1 [ 0.802833] pnp 00:0c: add mem 0xfffed000-0xfffeffff flags 0x1 [ 0.802833] pnp 00:0c: PNP0c01: calling quirk_system_pci_resources+0x0/0x15c [ 0.802833] pnp 00:0c: Plug and Play ACPI device, IDs PNP0c01 (active) [ 0.802833] pnp: PnP ACPI: found 13 devices [ 0.806833] ACPI: ACPI bus type pnp unregistered [ 0.810833] usbcore: registered new interface driver usbfs [ 0.814833] usbcore: registered new interface driver hub [ 0.818833] usbcore: registered new device driver usb [ 0.822833] PCI: Using ACPI for IRQ routing [ 0.842833] PCI-DMA: Disabling AGP. [ 0.846833] PCI-DMA: aperture base @ 4000000 size 65536 KB [ 0.850833] PCI-DMA: using GART IOMMU. [ 0.854838] PCI-DMA: Reserving 64MB of IOMMU area in the AGP aperture [ 0.859064] hpet0: at MMIO 0xfefff000, IRQs 2, 8, 31 [ 0.863064] hpet0: 3 32-bit timers, 25000000 Hz [ 0.867064] ACPI: RTC can wake from S4 [ 0.870838] Switched to high resolution mode on CPU 0 [ 0.874834] Switched to high resolution mode on CPU 1 [ 0.894822] pnp: the driver 'system' has been registered [ 0.894841] system 00:01: ioport range 0x1000-0x107f has been reserved [ 0.899813] system 00:01: ioport range 0x1080-0x10ff has been reserved [ 0.907811] system 00:01: ioport range 0x1400-0x147f has been reserved [ 0.915813] system 00:01: ioport range 0x1480-0x14ff has been reserved [ 0.922370] system 00:01: ioport range 0x1800-0x187f has been reserved [ 0.928922] system 00:01: ioport range 0x1880-0x18ff has been reserved [ 0.935471] system 00:01: driver attached [ 0.935478] system 00:02: ioport range 0x4d0-0x4d1 has been reserved [ 0.942026] system 00:02: ioport range 0x800-0x87f has been reserved [ 0.948412] system 00:02: ioport range 0x290-0x297 has been reserved [ 0.954784] system 00:02: driver attached [ 0.954797] system 00:0b: iomem range 0xf0000000-0xf3ffffff could not be reserved [ 0.962296] system 00:0b: driver attached [ 0.962303] system 00:0c: iomem range 0xcf400-0xcffff has been reserved [ 0.968936] system 00:0c: iomem range 0xf0000-0xf7fff could not be reserved [ 0.975331] system 00:0c: iomem range 0xf8000-0xfbfff could not be reserved [ 0.982316] system 00:0c: iomem range 0xfc000-0xfffff could not be reserved [ 0.989303] system 00:0c: iomem range 0xfefff000-0xfefff0ff could not be reserved [ 0.996804] system 00:0c: iomem range 0xdfee0000-0xdfefffff could not be reserved [ 1.004304] system 00:0c: iomem range 0xffff0000-0xffffffff could not be reserved [ 1.011804] system 00:0c: iomem range 0x0-0x9ffff could not be reserved [ 1.018437] system 00:0c: iomem range 0x100000-0xdfedffff could not be reserved [ 1.025765] system 00:0c: iomem range 0xfec00000-0xfec00fff could not be reserved [ 1.033263] system 00:0c: iomem range 0xfee00000-0xfeefffff could not be reserved [ 1.040763] system 00:0c: iomem range 0xfefff000-0xfeffffff could not be reserved [ 1.048264] system 00:0c: iomem range 0xfff80000-0xfff80fff could not be reserved [ 1.055763] system 00:0c: iomem range 0xfff90000-0xfffbffff could not be reserved [ 1.062796] system 00:0c: iomem range 0xfffed000-0xfffeffff could not be reserved [ 1.070303] system 00:0c: driver attached [ 1.073804] PCI: Bridge: 0000:00:06.0 [ 1.077488] IO window: a000-afff [ 1.080916] MEM window: 0xfde00000-0xfdefffff [ 1.085471] PREFETCH window: 0x00000000f4000000-0x00000000f40fffff [ 1.091847] PCI: Bridge: 0000:00:0a.0 [ 1.095794] IO window: disabled. [ 1.096364] MEM window: disabled. [ 1.099873] PREFETCH window: disabled. [ 1.103824] PCI: Bridge: 0000:00:0b.0 [ 1.107785] IO window: disabled. [ 1.111780] MEM window: disabled. [ 1.115780] PREFETCH window: disabled. [ 1.119777] PCI: Bridge: 0000:00:0c.0 [ 1.123773] IO window: disabled. [ 1.127772] MEM window: disabled. [ 1.131768] PREFETCH window: disabled. [ 1.135766] PCI: Bridge: 0000:00:0d.0 [ 1.141414] IO window: disabled. [ 1.144850] MEM window: disabled. [ 1.148358] PREFETCH window: disabled. [ 1.152308] PCI: Bridge: 0000:00:0e.0 [ 1.155995] IO window: disabled. [ 1.159749] MEM window: disabled. [ 1.163179] PREFETCH window: disabled. [ 1.167129] PCI: Bridge: 0000:00:0f.0 [ 1.170815] IO window: 9000-9fff [ 1.174330] MEM window: 0xfdd00000-0xfddfffff [ 1.178334] PREFETCH window: 0x00000000e0000000-0x00000000efffffff [ 1.186314] PCI: Setting latency timer of device 0000:00:06.0 to 64 [ 1.186325] PCI: Setting latency timer of device 0000:00:0a.0 to 64 [ 1.186332] PCI: Setting latency timer of device 0000:00:0b.0 to 64 [ 1.186338] PCI: Setting latency timer of device 0000:00:0c.0 to 64 [ 1.186344] PCI: Setting latency timer of device 0000:00:0d.0 to 64 [ 1.186351] PCI: Setting latency timer of device 0000:00:0e.0 to 64 [ 1.186357] PCI: Setting latency timer of device 0000:00:0f.0 to 64 [ 1.186405] NET: Registered protocol family 2 [ 1.227775] IP route cache hash table entries: 131072 (order: 8, 1048576 bytes) [ 1.238023] TCP established hash table entries: 524288 (order: 11, 8388608 bytes) [ 1.246555] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) [ 1.253747] TCP: Hash tables configured (established 524288 bind 65536) [ 1.260706] TCP reno registered [ 1.275080] NET: Registered protocol family 1 [ 1.279563] checking if image is initramfs... it is [ 1.782021] Freeing initrd memory: 7593k freed [ 1.790026] audit: initializing netlink socket (disabled) [ 1.795457] type=2000 audit(1136078633.777:1): initialized [ 1.804918] Total HugeTLB memory allocated, 0 [ 1.809615] VFS: Disk quotas dquot_6.5.1 [ 1.813590] Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 1.820098] msgmni has been set to 7935 [ 1.824097] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) [ 1.831511] io scheduler noop registered [ 1.835466] io scheduler anticipatory registered [ 1.839579] io scheduler deadline registered [ 1.842929] io scheduler cfq registered (default) [ 1.865099] pci 0000:00:05.0: Enabling HT MSI Mapping [ 1.873062] pci 0000:00:05.1: Enabling HT MSI Mapping [ 1.878147] pci 0000:00:05.2: Enabling HT MSI Mapping [ 1.883226] pci 0000:00:06.0: Enabling HT MSI Mapping [ 1.888312] pci 0000:00:06.1: Enabling HT MSI Mapping [ 1.893452] pci 0000:00:08.0: Enabling HT MSI Mapping [ 1.898532] pci 0000:00:0a.0: Enabling HT MSI Mapping [ 1.903617] pci 0000:00:0b.0: Enabling HT MSI Mapping [ 1.908699] pci 0000:00:0c.0: Enabling HT MSI Mapping [ 1.913798] pci 0000:00:0d.0: Enabling HT MSI Mapping [ 1.918882] pci 0000:00:0e.0: Enabling HT MSI Mapping [ 1.923966] pci 0000:00:0f.0: Enabling HT MSI Mapping [ 1.929058] pci 0000:07:00.0: Boot video device [ 1.929327] PCI: Setting latency timer of device 0000:00:0a.0 to 64 [ 1.929346] assign_interrupt_mode Found MSI capability [ 1.934152] Allocate Port Service[0000:00:0a.0:pcie00] [ 1.935429] Allocate Port Service[0000:00:0a.0:pcie03] [ 1.935429] PCI: Setting latency timer of device 0000:00:0b.0 to 64 [ 1.935429] assign_interrupt_mode Found MSI capability [ 1.939445] Allocate Port Service[0000:00:0b.0:pcie00] [ 1.940732] Allocate Port Service[0000:00:0b.0:pcie03] [ 1.940732] PCI: Setting latency timer of device 0000:00:0c.0 to 64 [ 1.940732] assign_interrupt_mode Found MSI capability [ 1.946036] Allocate Port Service[0000:00:0c.0:pcie00] [ 1.946036] Allocate Port Service[0000:00:0c.0:pcie03] [ 1.946036] PCI: Setting latency timer of device 0000:00:0d.0 to 64 [ 1.946036] assign_interrupt_mode Found MSI capability [ 1.950052] Allocate Port Service[0000:00:0d.0:pcie00] [ 1.951333] Allocate Port Service[0000:00:0d.0:pcie03] [ 1.951333] PCI: Setting latency timer of device 0000:00:0e.0 to 64 [ 1.951333] assign_interrupt_mode Found MSI capability [ 1.955348] Allocate Port Service[0000:00:0e.0:pcie00] [ 1.956634] Allocate Port Service[0000:00:0e.0:pcie03] [ 1.956634] PCI: Setting latency timer of device 0000:00:0f.0 to 64 [ 1.956634] assign_interrupt_mode Found MSI capability [ 1.960650] Allocate Port Service[0000:00:0f.0:pcie00] [ 1.961923] Allocate Port Service[0000:00:0f.0:pcie03] [ 1.962062] hpet_resources: 0xfefff000 is busy [ 1.965045] Linux agpgart interface v0.103 [ 1.969049] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled [ 1.977117] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 1.983268] pnp: the driver 'serial' has been registered [ 1.983268] 00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 1.990368] serial 00:09: driver attached [ 1.990368] brd: module loaded [ 1.997583] input: Macintosh mouse button emulation as /class/input/input0 [ 2.006107] pnp: the driver 'i8042 kbd' has been registered [ 2.006107] pnp: the driver 'i8042 aux' has been registered [ 2.006107] pnp: the driver 'i8042 kbd' has been unregistered [ 2.006107] pnp: the driver 'i8042 aux' has been unregistered [ 2.006107] PNP: No PS/2 controller found. Probing ports directly. [ 2.013391] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 2.017398] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 2.045389] mice: PS/2 mouse device common for all mice [ 2.050731] pnp: the driver 'rtc_cmos' has been registered [ 2.050731] rtc_cmos 00:05: rtc core: registered rtc_cmos as rtc0 [ 2.056861] rtc0: alarms up to one year, y3k [ 2.060985] rtc_cmos 00:05: driver attached [ 2.061297] cpuidle: using governor ladder [ 2.065301] cpuidle: using governor menu [ 2.069254] No iBFT detected. [ 2.072614] TCP cubic registered [ 2.072619] NET: Registered protocol family 17 [ 2.080510] registered taskstats version 1 [ 2.084706] rtc_cmos 00:05: setting system clock to 2006-01-01 01:23:55 UTC (1136078635) [ 2.092787] Freeing unused kernel memory: 392k freed [ 2.182265] ACPI: PNP0C0B:00 is registered as cooling_device0 [ 2.188231] ACPI: Fan [FAN] (on) [ 2.196753] ACPI: ACPI0007:00 is registered as cooling_device1 [ 2.205628] ACPI: ACPI0007:01 is registered as cooling_device2 [ 2.212750] ACPI: LNXTHERM:01 is registered as thermal_zone0 [ 2.219578] ACPI: Thermal Zone [THRM] (40 C) [ 2.505755] Uniform Multi-Platform E-IDE driver [ 2.512578] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx [ 2.522539] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver [ 2.522995] ACPI: PCI Interrupt Link [APCF] enabled at IRQ 23 [ 2.528987] ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [APCF] -> GSI 23 (level, low) -> IRQ 23 [ 2.537677] PCI: Setting latency timer of device 0000:00:02.0 to 64 [ 2.537680] ohci_hcd 0000:00:02.0: OHCI Host Controller [ 2.543213] ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1 [ 2.551114] ohci_hcd 0000:00:02.0: irq 23, io mem 0xfe02f000 [ 2.607586] Floppy drive(s): fd0 is 1.44M [ 2.618918] usb usb1: configuration #1 chosen from 1 choice [ 2.622952] hub 1-0:1.0: USB hub found [ 2.626845] hub 1-0:1.0: 10 ports detected [ 2.635028] FDC 0 is a post-1991 82077 [ 2.735057] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001 [ 2.742918] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.750918] usb usb1: Product: OHCI Host Controller [ 2.758914] usb usb1: Manufacturer: Linux 2.6.26-2-amd64 ohci_hcd [ 2.766395] usb usb1: SerialNumber: 0000:00:02.0 [ 2.773535] ACPI: PCI Interrupt Link [APCL] enabled at IRQ 22 [ 2.779537] ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [APCL] -> GSI 22 (level, low) -> IRQ 22 [ 2.788361] PCI: Setting latency timer of device 0000:00:02.1 to 64 [ 2.788364] ehci_hcd 0000:00:02.1: EHCI Host Controller [ 2.793839] ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 2 [ 2.798716] ehci_hcd 0000:00:02.1: debug port 1 [ 2.806431] PCI: cache line size of 64 is not supported by device 0000:00:02.1 [ 2.806444] ehci_hcd 0000:00:02.1: irq 22, io mem 0xfe02e000 [ 2.820997] ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 [ 2.826825] usb usb2: configuration #1 chosen from 1 choice [ 2.834778] hub 2-0:1.0: USB hub found [ 2.840512] hub 2-0:1.0: 10 ports detected [ 2.946642] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 [ 2.950997] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.960378] usb usb2: Product: EHCI Host Controller [ 2.966548] usb usb2: Manufacturer: Linux 2.6.26-2-amd64 ehci_hcd [ 2.974251] usb usb2: SerialNumber: 0000:00:02.1 [ 2.978547] forcedeth: Reverse Engineered nForce ethernet driver. Version 0.61. [ 2.986569] ACPI: PCI Interrupt Link [APCH] enabled at IRQ 21 [ 2.992528] ACPI: PCI Interrupt 0000:00:08.0[A] -> Link [APCH] -> GSI 21 (level, low) -> IRQ 21 [ 3.002759] PCI: Setting latency timer of device 0000:00:08.0 to 64 [ 3.455738] usb 1-2: new low speed USB device using ohci_hcd and address 2 [ 3.520180] forcedeth 0000:00:08.0: ifname eth0, PHY OUI 0x5043 @ 1, addr 00:0e:a6:f9:9e:86 [ 3.528832] forcedeth 0000:00:08.0: highdma csum vlan pwrctl mgmt timirq gbit lnktim msi desc-v3 [ 3.551853] r8169 Gigabit Ethernet driver 2.2LK-NAPI loaded [ 3.559120] ACPI: PCI Interrupt Link [APC1] enabled at IRQ 16 [ 3.566695] ACPI: PCI Interrupt 0000:01:06.0[A] -> Link [APC1] -> GSI 16 (level, low) -> IRQ 16 [ 3.575038] eth1: RTL8110s at 0xffffc20000628000, 00:e0:4c:6a:11:82, XID 04000000 IRQ 16 [ 3.594682] NFORCE-MCP55: 0000:00:04.0 (rev a1) UDMA133 controller [ 3.594689] NFORCE-MCP55: IDE controller (0x10de:0x036e rev 0xa1) at PCI slot 0000:00:04.0 [ 3.608320] NFORCE-MCP55: not 100% native mode: will probe irqs later [ 3.616301] NFORCE-MCP55: IDE port disabled [ 3.619369] ide0: BM-DMA at 0xf000-0xf007 [ 3.623913] Probing IDE interface ide0... [ 3.637390] No dock devices found. [ 3.645397] SCSI subsystem initialized [ 3.657865] libata version 3.00 loaded. [ 3.705391] usb 1-2: configuration #1 chosen from 1 choice [ 3.717658] usb 1-2: New USB device found, idVendor=0603, idProduct=00f2 [ 3.724716] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 3.729652] usb 1-2: Product: USB Keyboard [ 3.734197] usb 1-2: Manufacturer: NOVATEK [ 3.749390] usbcore: registered new interface driver hiddev [ 3.763104] input: NOVATEK USB Keyboard as /class/input/input1 [ 3.801686] input,hidraw0: USB HID v1.10 Keyboard [NOVATEK USB Keyboard] on usb-0000:00:02.0-2 [ 3.822265] input: NOVATEK USB Keyboard as /class/input/input2 [ 3.841298] input,hiddev96,hidraw1: USB HID v1.10 Device [NOVATEK USB Keyboard] on usb-0000:00:02.0-2 [ 3.849543] usbcore: registered new interface driver usbhid [ 3.855338] usbhid: v2.6:USB HID core driver [ 4.205136] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 [ 4.296984] sata_nv 0000:00:05.0: version 3.5 [ 4.297239] ACPI: PCI Interrupt Link [APSI] enabled at IRQ 20 [ 4.303227] ACPI: PCI Interrupt 0000:00:05.0[A] -> Link [APSI] -> GSI 20 (level, low) -> IRQ 20 [ 4.314796] sata_nv 0000:00:05.0: Using SWNCQ mode [ 4.317468] PCI: Setting latency timer of device 0000:00:05.0 to 64 [ 4.319912] scsi0 : sata_nv [ 4.322946] scsi1 : sata_nv [ 4.323908] ata1: SATA max UDMA/133 cmd 0x9f0 ctl 0xbf0 bmdma 0xdc00 irq 20 [ 4.331725] ata2: SATA max UDMA/133 cmd 0x970 ctl 0xb70 bmdma 0xdc08 irq 20 [ 4.813116] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 5.081506] ata1.00: HPA detected: current 2930277168, native 18446744072344861488 [ 5.099483] ata1.00: ATA-8: ST31500341AS, CC1H, max UDMA/133 [ 5.107480] ata1.00: 2930277168 sectors, multi 1: LBA48 NCQ (depth 31/32) [ 5.172805] ata1.00: configured for UDMA/133 [ 5.647513] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 5.883345] ata2.00: HPA detected: current 2930277168, native 18446744072344861488 [ 5.897193] ata2.00: ATA-8: ST31500341AS, CC1H, max UDMA/133 [ 5.905191] ata2.00: 2930277168 sectors, multi 1: LBA48 NCQ (depth 31/32) [ 5.971056] ata2.00: configured for UDMA/133 [ 5.975015] scsi 0:0:0:0: Direct-Access ATA ST31500341AS CC1H PQ: 0 ANSI: 5 [ 5.987633] scsi 1:0:0:0: Direct-Access ATA ST31500341AS CC1H PQ: 0 ANSI: 5 [ 5.996440] ACPI: PCI Interrupt Link [APSJ] enabled at IRQ 23 [ 6.002352] ACPI: PCI Interrupt 0000:00:05.1[B] -> Link [APSJ] -> GSI 23 (level, low) -> IRQ 23 [ 6.011383] sata_nv 0000:00:05.1: Using SWNCQ mode [ 6.016390] PCI: Setting latency timer of device 0000:00:05.1 to 64 [ 6.018729] scsi2 : sata_nv [ 6.022372] scsi3 : sata_nv [ 6.025490] ata3: SATA max UDMA/133 cmd 0x9e0 ctl 0xbe0 bmdma 0xc800 irq 23 [ 6.032673] ata4: SATA max UDMA/133 cmd 0x960 ctl 0xb60 bmdma 0xc808 irq 23 [ 6.370380] ata3: SATA link down (SStatus 0 SControl 300) [ 6.953789] ata4: SATA link down (SStatus 0 SControl 300) [ 7.096263] ACPI: PCI Interrupt Link [ASA2] enabled at IRQ 22 [ 7.102230] ACPI: PCI Interrupt 0000:00:05.2[C] -> Link [ASA2] -> GSI 22 (level, low) -> IRQ 22 [ 7.111267] sata_nv 0000:00:05.2: Using SWNCQ mode [ 7.118651] PCI: Setting latency timer of device 0000:00:05.2 to 64 [ 7.119358] scsi4 : sata_nv [ 7.122654] scsi5 : sata_nv [ 7.125753] ata5: SATA max UDMA/133 cmd 0xc400 ctl 0xc000 bmdma 0xb400 irq 22 [ 7.133139] ata6: SATA max UDMA/133 cmd 0xbc00 ctl 0xb800 bmdma 0xb408 irq 22 [ 7.467269] ata5: SATA link down (SStatus 0 SControl 300) [ 8.315049] ata6: SATA link down (SStatus 0 SControl 300) [ 8.331358] Driver 'sd' needs updating - please use bus_type methods [ 8.339274] sd 0:0:0:0: [sda] 2930277168 512-byte hardware sectors (1500302 MB) [ 8.347175] sd 0:0:0:0: [sda] Write Protect is off [ 8.352211] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 8.352243] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 8.361648] sd 0:0:0:0: [sda] 2930277168 512-byte hardware sectors (1500302 MB) [ 8.369608] sd 0:0:0:0: [sda] Write Protect is off [ 8.374655] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 8.374685] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 8.386420] sda: sda1 sda2 sda3 [ 8.396625] sd 0:0:0:0: [sda] Attached SCSI disk [ 8.401479] sd 1:0:0:0: [sdb] 2930277168 512-byte hardware sectors (1500302 MB) [ 8.409358] sd 1:0:0:0: [sdb] Write Protect is off [ 8.414369] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 [ 8.414402] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 8.427310] sd 1:0:0:0: [sdb] 2930277168 512-byte hardware sectors (1500302 MB) [ 8.433668] sd 1:0:0:0: [sdb] Write Protect is off [ 8.438657] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 [ 8.438685] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 8.449685] sdb: sdb1 sdb2 sdb3 [ 8.466482] sd 1:0:0:0: [sdb] Attached SCSI disk [ 8.634544] md: raid1 personality registered for level 1 [ 8.646546] md: md0 stopped. [ 8.664003] md: bind [ 8.667125] md: bind [ 8.682377] raid1: raid set md0 active with 2 out of 2 mirrors [ 8.687623] md: md1 stopped. [ 8.722260] md: bind [ 8.725306] md: bind [ 8.739555] raid1: raid set md1 active with 2 out of 2 mirrors [ 8.745819] md: md2 stopped. [ 8.791090] md: bind [ 8.794153] md: bind [ 8.796910] md: kicking non-fresh sdb3 from array! [ 8.801947] md: unbind [ 8.807922] md: export_rdev(sdb3) [ 8.823963] raid1: raid set md2 active with 1 out of 2 mirrors [ 8.896114] device-mapper: uevent: version 1.0.3 [ 8.904113] device-mapper: ioctl: 4.13.0-ioctl (2007-10-18) initialised: dm-devel@redhat.com [ 8.991564] PM: Starting manual resume from disk [ 9.006344] SGI XFS with ACLs, security attributes, realtime, large block/inode numbers, no debug enabled [ 9.018669] SGI XFS Quota Management subsystem [ 9.025954] Filesystem "dm-0": Disabling barriers, not supported by the underlying device [ 9.043653] XFS mounting filesystem dm-0 [ 9.143891] Ending clean XFS mount for filesystem: dm-0 [ 10.021188] udevd version 125 started [ 10.522281] input: Power Button (FF) as /class/input/input3 [ 10.591013] ACPI: Power Button (FF) [PWRF] [ 10.595344] input: Power Button (CM) as /class/input/input4 [ 10.656171] ACPI: Power Button (CM) [PWRB] [ 10.806620] i2c-adapter i2c-0: nForce2 SMBus adapter at 0x1c00 [ 10.812649] i2c-adapter i2c-1: nForce2 SMBus adapter at 0x1c40 [ 10.988483] ACPI: PCI Interrupt Link [AAZA] enabled at IRQ 21 [ 10.992494] ACPI: PCI Interrupt 0000:00:06.1[B] -> Link [AAZA] -> GSI 21 (level, low) -> IRQ 21 [ 11.001578] PCI: Setting latency timer of device 0000:00:06.1 to 64 [ 11.032112] input: PC Speaker as /class/input/input5 [ 11.136845] Error: Driver 'pcspkr' is already registered, aborting... [ 11.252001] pnp: the driver 'parport_pc' has been registered [ 11.252021] parport_pc 00:0a: reported by Plug and Play ACPI [ 11.257981] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE,EPP] [ 11.359921] parport_pc 00:0a: driver attached [ 11.426494] ACPI: PCI Interrupt Link [APC7] enabled at IRQ 16 [ 11.432456] ACPI: PCI Interrupt 0000:07:00.1[B] -> Link [APC7] -> GSI 16 (level, low) -> IRQ 16 [ 11.441544] PCI: Setting latency timer of device 0000:07:00.1 to 64 [ 12.481039] Adding 1951800k swap on /dev/md1. Priority:-1 extents:1 across:1951800k [ 12.571560] Filesystem "dm-0": Disabling barriers, not supported by the underlying device [ 13.574353] loop: module loaded [ 14.449063] kjournald starting. Commit interval 5 seconds [ 14.457884] EXT3 FS on md0, internal journal [ 14.461163] EXT3-fs: mounted filesystem with ordered data mode. [ 15.443843] r8169: eth1: link down [ 16.142833] NET: Registered protocol family 10 [ 16.150325] lo: Disabled Privacy Extensions [ 16.155103] ADDRCONF(NETDEV_UP): eth1: link is not ready [ 27.845676] eth0: no IPv6 routers present [ 238.258132] i2c /dev entries driver [ 381.504006] it87: Found IT8716F chip at 0x290, revision 1 [ 381.507372] it87: in3 is VCC (+5V) [ 381.511355] it87: in7 is VCCH (+5V Stand-By)