smartctl version 5.38 [i686-pc-linux-gnu] Copyright (C) 2002-8 Bruce Allen Home page is http://smartmontools.sourceforge.net/ === START OF INFORMATION SECTION === Model Family: Seagate Momentus 7200.2 Device Model: ST9160823AS Serial Number: 5NK0TTK7 Firmware Version: 3.CME User Capacity: 160,041,885,696 bytes Device is: In smartctl database [for details use: -P show] ATA Version is: 7 ATA Standard is: Exact ATA specification draft version not indicated Local Time is: Wed Jun 24 19:41:26 2009 UTC SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED See vendor-specific Attribute list for marginal Attributes. General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 426) seconds. Offline data collection capabilities: (0x53) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 58) minutes. SCT capabilities: (0x0001) SCT Status supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 087 065 034 Pre-fail Always - 32034360 3 Spin_Up_Time 0x0003 100 099 000 Pre-fail Always - 0 4 Start_Stop_Count 0x0032 001 001 020 Old_age Always FAILING_NOW 1125680 5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0 7 Seek_Error_Rate 0x000f 071 060 030 Pre-fail Always - 25857283884 9 Power_On_Hours 0x0032 091 091 000 Old_age Always - 73972221747095 10 Spin_Retry_Count 0x0013 100 098 034 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 670 184 Unknown_Attribute 0x0032 100 253 000 Old_age Always - 0 187 Reported_Uncorrect 0x003a 098 098 000 Old_age Always - 2 189 High_Fly_Writes 0x0022 100 100 045 Old_age Always - 0 190 Airflow_Temperature_Cel 0x0032 062 042 000 Old_age Always - 38 (Lifetime Min/Max 38/38) 191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 3 192 Power-Off_Retract_Count 0x0022 100 100 000 Old_age Always - 36 193 Load_Cycle_Count 0x001a 001 001 000 Old_age Always - 1126160 194 Temperature_Celsius 0x0012 038 058 000 Old_age Always - 38 (0 16 0 0) 195 Hardware_ECC_Recovered 0x0010 098 065 000 Old_age Offline - 32034360 196 Reallocated_Event_Count 0x003e 093 093 000 Old_age Always - 257165461821769 197 Current_Pending_Sector 0x0000 100 100 000 Old_age Offline - 1 198 Offline_Uncorrectable 0x0032 100 100 000 Old_age Always - 1 199 UDMA_CRC_Error_Count 0x0000 200 200 000 Old_age Offline - 0 200 Multi_Zone_Error_Rate 0x0000 100 253 000 Old_age Offline - 0 202 TA_Increase_Count 0x0000 100 253 000 Old_age Offline - 0 254 Unknown_Attribute 0x0000 100 253 000 Old_age Offline - 0 SMART Error Log Version: 1 ATA Error Count: 44 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 44 occurred at disk power-on lifetime: 8086 hours (336 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 41 00 00 e0 Error: UNC at LBA = 0x00000041 = 65 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 29 10 3f 3f 00 00 e0 00 00:00:09.265 READ MULTIPLE EXT 25 10 3f 3f 00 00 e0 00 00:00:15.227 READ DMA EXT 25 10 3f 00 00 00 e0 00 00:00:12.724 READ DMA EXT ef 10 03 ff ff 00 e0 00 00:00:12.681 SET FEATURES [Reserved for Serial ATA] ef 03 45 ff ff 00 e0 00 00:00:12.677 SET FEATURES [Set transfer mode] Error 43 occurred at disk power-on lifetime: 8086 hours (336 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 41 00 00 e0 Error: UNC at LBA = 0x00000041 = 65 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 10 3f 3f 00 00 e0 00 00:00:09.265 READ DMA EXT 25 10 3f 00 00 00 e0 00 00:00:08.931 READ DMA EXT ef 10 03 ff ff 00 e0 00 00:00:12.724 SET FEATURES [Reserved for Serial ATA] ef 03 45 ff ff 00 e0 00 00:00:12.681 SET FEATURES [Set transfer mode] ef 03 0c ff ff 00 e0 00 00:00:12.677 SET FEATURES [Set transfer mode] Error 42 occurred at disk power-on lifetime: 8086 hours (336 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 41 00 00 e0 Error: UNC at LBA = 0x00000041 = 65 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c4 ff 02 41 00 00 e0 00 00:00:44.394 READ MULTIPLE c8 ff 02 41 00 00 e0 00 00:00:44.391 READ DMA ef 10 03 ff ff 00 e0 00 00:00:44.390 SET FEATURES [Reserved for Serial ATA] ef 03 45 ff ff 00 e0 00 00:00:44.390 SET FEATURES [Set transfer mode] ef 03 0c ff ff 00 e0 00 00:00:44.390 SET FEATURES [Set transfer mode] Error 41 occurred at disk power-on lifetime: 8086 hours (336 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 41 00 00 e0 Error: UNC at LBA = 0x00000041 = 65 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 ff 02 41 00 00 e0 00 00:00:44.394 READ DMA ef 10 03 ff ff 00 e0 00 00:00:44.391 SET FEATURES [Reserved for Serial ATA] ef 03 45 ff ff 00 e0 00 00:00:44.390 SET FEATURES [Set transfer mode] ef 03 0c ff ff 00 e0 00 00:00:44.390 SET FEATURES [Set transfer mode] c6 ff 10 ff ff 00 e0 00 00:00:44.390 SET MULTIPLE MODE Error 40 occurred at disk power-on lifetime: 8086 hours (336 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 41 00 00 e0 Error: UNC at LBA = 0x00000041 = 65 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c4 ff 02 41 00 00 e0 00 00:00:39.084 READ MULTIPLE c8 ff 02 41 00 00 e0 00 00:00:39.042 READ DMA ef 10 03 ff ff 00 e0 00 00:00:36.267 SET FEATURES [Reserved for Serial ATA] ef 03 45 ff ff 00 e0 00 00:00:33.789 SET FEATURES [Set transfer mode] ef 03 0c ff ff 00 e0 00 00:00:33.786 SET FEATURES [Set transfer mode] SMART Self-test log structure revision number 1 SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.